Inovonics EN1210W-60 User Manual download pdf

5/21/14 04858I © Inovonics, 2014 - www.inovonics.com

EN1210W/EN1210W-60 EchoStream® Door/

Window Transmitter with Reed Switch

1 Overview

The EN1210W and EN1210W-60 are universal transmitters with one

internal contact magnetic reed switch. Inovonics mult-function add-on

receivers will support both inputs as separate devices.

Note: The transmitter contains both a wired input and an input activated

by a reed switch and magnet. The reed switch and magnet must be used

unless the application (control panel) specifically supports both inputs as

separate devices. Use of the wired input is optional.

Note: For UL 2560 installations, refer to the EN6080 Area Control

Gateway Installation Instructions.

1.1 Maximum Number of Repeaters for a UL2560 Installation

To achieve the 99.99% alarm message reliability required for UL2560

compliance, system installations must operate within the following limits

for end device and repeater counts.

1.2 Inovonics Wireless Contact Information

If you have any problems with this procedure, contact Inovonics Wireless

technical services:

• E-mail: support@inovonics.com.

• Phone: (800) 782-2709.

1.3 Internal Components

Figure 1 Components

1.4 What’s In The Carton

• Three wall mount screws.

• Three wall mount anchors.

• Two selection jumpers.

• One 3.0V lithium battery.

• One magnet.

2 Installation and Startup

2.1 Installation Notes

• These products are designed to be installed and maintained by

professional security technicians.

• Products are intended for indoor use.

• Manually test all products weekly.

2.2 Install the Battery

1. Pry the top lip of the mounting bracket up, and lift the bracket off of the

transmitter.

2. Use your thumb to depress the housing release tab on the bottom of

the transmitter; separate the housing.

3. Install the new battery.

4. Press the reset button to initialize the transmitter.

2.3 Select the Frequency Band

EchoStream products are able to use a range of radio frequencies, and

must be configured for your geographic area. This product ships with a

default frequency range of 902-928 MHz for use in North America. If you

are using the product in North America, skip to section 2.4, “Select Input

Type”; if you are using the product in Australia or New Zealand, you will

need to configure the transmitter.

5. Place a selection jumper on the appropriate frequency band selection

pins.

• Place the jumper on the right two pins, marked NZ, to set the

frequency range to 921-928 MHz for New Zealand.

• Place the jumper on the left two pins, marked AU, to set the

frequency range to 915-928 MHz for Australia.

6. Press the reset button to complete configuration.

Caution: When pressing the reset button, make sure you don’t also touch

the frequency band selection pins. Touching the frequency band selection

pins while pressing the reset button can inadvertently set the transmitter to

the wrong frequency band.

2.4 Select Input Type

The N/O-N/C selection pins allow the choice of a normally open or

normally closed state for the contact circuit wired to the input terminal. The

transmitter is shipped set for normally open, with a selection jumper on the

N/O selections pins. If you are using the product in a normally open state,

skip to section 2.5, “Register the Transmitter”; if you are using the product

in a normally closed state, you will need to configure the transmitter:

7. Remove the selection jumper from the selection pins to select

normally closed.

8. Press the reset button to complete configuration.

Caution: If only the reed switch and magnet are to be used, normally

open should be selected.

2.5 Register the Transmitter

Transmitters must be registered with the system in order to be monitored

and supervised. The EN1210W sends a check-in message every three

minutes; the EN1210W-60 sends a check-in message every 60 minutes.

Each transmitter has a unique factory-programmed identification number.

Refer to the receiver installation instructions for details on registering a

transmitter.

Note: For UL 2560 installations, transmitters must have a minimum

check-in time of 60 minutes.

9. When prompted by the receiver to reset transmitter, press the reset

button.

10. Replace the cover.

11. Test the transmitter by activating each of the conditions and ensuring

an appropriate response.

2.6 Mount the Transmitter

12. Mount the bracket on the wall with the screws provided, ensuring

room for the magnet where indicated by the mounting directions on

the inside of the bracket.

Figure 2 Mount the bracket

13. Mount the magnet where indicated by the mounting arrow on the

inside of the bracket,

14. Clip the transmitter onto the bracket. Hook the bottom catch first, then

press the top into place.

15. As desired, use the third mounting screw to secure the housing

through the screw hole located beneath the battery.

End Devices Maximum

Repeaters

150 397

250 386

350 375

500 360

1000 313

2000 238

3000 184

A Frequency band selection

pins

B Reset button

C Antenna D Input terminal

E N/O - N/C selection pins F Tamper button and spring

G Reed switch

Mount the magnet

per the mounting

directions on the

inside of the bracket

Mounting

holes

1 2

Summary of Contents

Page 1 - 2 Installation and Startup

5/21/14 04858I © Inovonics, 2014 - www.inovonics.comEN1210W/EN1210W-60 EchoStream® Door/Window Transmitter with Reed Switch1 OverviewThe EN1210W and E

Page 2 - 5 Specifications

5/21/14 04858I © Inovonics, 2014 - www.inovonics.comNote: Accessing this screw on an active transmitter requires opening the housing and removing the

Related models: EN1210W

Comments to this Manuals

No comments

Inovonics EN1210W-60 User Manual

Browse online or download User Manual for Communication Inovonics EN1210W-60. Inovonics EN1210W-60 User Manual

Summary of Contents

Related models: EN1210W

Comments to this Manuals

Related products and manuals for Communication Inovonics EN1210W-60