Inovonics EE4216MR User Manual download pdf (Page 2)

Caution: Turning off supervision can jeopardize the integrity of your system. Inovonics

does not recommend turning off supervision. For supervision to function correctly, the

supervision time must be set for an interval greater than the transmitter check-in time.

a. Use the Up and Down buttons to adjust the supervision time; press the Enter

button to select.

b. Use the Up and Down buttons to toggle between Hrs (hours) and Min (minutes);

press the Enter button to select.

Select Security/Repeater Configures point’s alarm and alert bits as either a repeater

or a security transmitter.

a. Use the Up and Down buttons to choose S

ELECT SECURITY for a security

transmitter or SELECT REPEATER for a repeater; press the Enter button to select.

1-4 Alarm Inputs Allows security transmitters with multiple alarm conditions to be

assigned a separate alarm point and output type for each individual condition.

a. Use the Up and Down buttons to select the number of alarm inputs for the

transmitter; press the Enter to select.

Alarm Out: Maps the security transmitter’s alarm condition(s) to alarm outputs.

a. Use the Up/Down buttons to scroll through the output numbers. Choosing - - will

disable alarm output.

b. Press Enter to select the output to use for the alarm condition.

Alarm Output Type Selects the output type for the alarm condition.

a. Use the Up/Down buttons to scroll through the following options:

• Follower: The output reflects the transmitter’s alarm status. Press the Enter

button to select.

• Latching: The output turns on when activated and remains on until the receiver

is reset. Press the Enter button to select.

• Toggle: The output changes state each time the device sends a new activation.

Press the Enter button to select.

NACTIVE displays when selected. Inactive time prevents output chatter. The

valid range is 2.0 to 99.5 seconds, in 0.5 second increments. Use the Up and

Down buttons to select; press the Enter button to select.

• Momentary: The output turns on for the programmed duration, then turns off,

regardless of the device status. Press the Enter button to select.

OMENT displays when selected. This sets the time that the output will stay

activated. The valid range 0.5 to 99.5 seconds, in 0.5 second increments. Use

the Up and Down buttons to select; press the Enter button to select.

Inactive Out: Maps transmitter/repeater inactivity fault output.

a. Use the Up/Down buttons to scroll through the output numbers. Choosing - - will

disable inactivity reporting.

b. Press Enter to select the output to use for this transmitter/repeater's inactivity

transmission.

Inactive Output Type Selects the output type for the inactive condition.

a. Use the Up/Down buttons to scroll through the following options:

• Follower: The output reflects the transmitter’s inactive status. Press the Enter

button to select.

• Latching: The output turns on when a inactive condition is sent and remains on

until the receiver is reset. Press the Enter button to select.

• Toggle: The output changes state each time the device sends a new inactive

condition. A minimum of five seconds must elapse before the output can send a

new inactive condition. Press the Enter button to select.

NACTIVE displays when selected. Inactive time prevents output chatter. The

valid range is 2.0 to 99.5 seconds, in 0.5 second increments. Use the Up and

Down buttons to select; press the Enter button to select.

• Momentary: The output turns on for the programmed duration, then turns off,

regardless of the device status. Press the Enter button to select.

OMENT displays when selected. This sets the time that the output will stay

activated. The valid range 0.5 to 99.5 seconds, in 0.5 second increments. Use

the Up and Down buttons to select; press the Enter button to select.

Tamper Out: Maps transmitter/repeater tamper fault output.

a. Use the Up/Down buttons to scroll through the output numbers. Choosing - - will

disable tamper output.

b. Press Enter to select the output to use for this transmitter/repeater's tamper

transmission.

Tamper Output Type Selects the output type for the tamper condition.

a. Use the Up/Down buttons to scroll through the following options:

• Follower: The output reflects the transmitter’s tamper status. Press the Enter

button to select.

• Latching: The output turns on when a tamper condition is sent and remains on

until the receiver is reset. Press the Enter button to select.

• Toggle: The output changes state each time the device sends a new tamper

condition. A minimum of five seconds must elapse before the output can send a

new tamper condition. Press the Enter button to select.

NACTIVE displays when selected. Inactive time prevents output chatter. The

valid range is 2.0 to 99.5 seconds, in 0.5 second increments. Use the Up and

Down buttons to select; press the Enter button to select.

• Momentary: The output turns on for the programmed duration, then turns off,

regardless of the device status. Press the Enter button to select.

OMENT displays when selected. This sets the time that the output will stay

activated. The valid range 0.5 to 99.5 seconds, in 0.5 second increments. Use

the Up and Down buttons to select; press the Enter button to select.

Low Batt Out: Maps transmitter/repeater low battery fault output.

a. Use the Up/Down buttons to scroll through the output numbers. Choosing - - will

disable low battery output.

b. Press Enter to select the output to use for this transmitter/repeater's low battery

transmission.

Low Battery Output Type Selects the output type for the low battery condition.

a. Use the Up/Down buttons to scroll through the following options:

• Follower: The output reflects the transmitter’s low battery status. Press the

Enter button to select.

• Latching: The output turns on when a low battery condition is sent and remains

on until the receiver is reset. Press the Enter button to select.

• Toggle: The output changes state each time the device sends a new low battery

condition. A minimum of five seconds must elapse before the output can send a

new low battery condition. Press the Enter button to select.

NACTIVE displays when selected. Inactive time prevents output chatter. The

valid range is 2.0 to 99.5 seconds, in 0.5 second increments. Use the Up and

Down buttons to select; press the Enter button to select.

• Momentary: The output turns on for the programmed duration, then turns off,

regardless of the device status. Press the Enter button to select.

OMENT displays when selected. This sets the time that the output will stay

activated. The valid range 0.5 to 99.5 seconds, in 0.5 second increments. Use

the Up and Down buttons to select; press the Enter button to select.

Line Power Loss Out: Maps repeater line power loss fault output.

a. Use the Up/Down buttons to scroll through the output numbers. Choosing - - will

disable line power loss output.

b. Press Enter to select the output to use for this repeater's line power loss

transmission.

Line Power Loss Output Type Selects the output type for the line power loss

condition.

a. Use the Up/Down buttons to scroll through the following options:

• Follower: The output reflects the repeater’s line power loss status. Press the

Enter button to select.

• Latching: The output turns on when a low battery condition is sent and remains

on until the receiver is reset. Press the Enter button to select.

• Toggle: The output changes state each time the device sends a new line power

loss condition. A minimum of five seconds must elapse before the output can

send a new line power loss condition. Press the Enter button to select.

NACTIVE displays when selected. Inactive time prevents output chatter. The

valid range is 2.0 to 99.5 seconds, in 0.5 second increments. Use the Up and

Down buttons to select; press the Enter button to select.

Momentary: The output turns on for the programmed duration, then turns off,

regardless of the device status. Press the Enter button to select.

OMENT displays when selected. This sets the time that the output will stay activated.

The valid range 0.5 to 99.5 seconds, in 0.5 second increments. Use the Up and Down

buttons to select; press the Enter button to select.

Text: Enter eight-character descriptive text for the transmitter/repeater

a. Use Up/Down buttons to scroll through the alphanumeric characters; press

Enter to select and advance to the next character. To select a space, press Enter

without selecting a digit.

Note: If you do not use all eight characters, you must enter spaces to the end of the

line.

b. When finished, press Enter again to complete selection.

2.7 Register Transmitter

The REGISTER TRANSMITTER option allows you to register a transmitter or repeater.

a. Use the Up and Down buttons to toggle between N for no and Y for yes to

choose whether or not you wish to register a transmitter/repeater to the point; press

Enter to select.

Note: You can always register a transmitter/repeater to the point at a later time using

the REGISTER XMITTER prompt in the INSTALL & SERVICE menu.

b. If you chose to register a transmitter/repeater at this time, press the transmitter/

repeater’s Reset button at the R

ESET XMITTER prompt.

2.8 Delete Point

The DELETE POINT option allows you to delete transmitter registration information from

all registered points, or a specific point. Programmed point information is not deleted;

just the registration identification number associated with the transmitters or

repeaters. To delete points:

1. From the I

NSTALL & SERVICE menu, use the Up and Down buttons to navigate to

the DELETE POINT prompt; press the Enter button.

2. The D

ELETE ALL? prompt displays. Use the Up and Down buttons to choose N for

no or Y for yes; press Enter to select.

3. If you selected no, the D

ELETE POINT prompt displays. Use the Up and Down

buttons to select a point to delete; press Enter to select.

4. Press the Enter button to return to the I

NSTALL & SERVICE menu.

2.9 Monitor Signal Strength

The SIGNAL STRENGTH option is used to measure signal strength and troubleshoot

installation problems.

1. At the S

IGNAL STRENGTH prompt, press Enter.

•P

OINT 01 displays, along with a signal quality of GOOD, WEAK or NO SIG.

Note: The point must have an active transmitter associated with it to display signal

strength.

2. Use the Up/Down buttons to scroll through the registered transmitters.

3. Press Enter again to view Level (LV) and Margin (MA).

• LV indicates the overall signal strength; MA indicates the signal strength minus

the background noise.

Note: Inovonics recommends an LV of four for most installations. For CENELEC,

Grade 2 installations, an LV of 10 or greater is required.

4. To reset signal data, use the Up/Down buttons to leave and return to the

transmitter you are monitoring.

2.10 CTS Type

The EE4216MR provides a signal to the control panel which can be used to ensure all

security devices in the system are active before allowing the system to be set. If used

by the control panel, the system cannot be set if the receiver has not heard from any

registered wireless devices within the last 20 minutes.

Note: The CTS signal can be used to block alarming conditions. This is useful when

performing system tests. For more information on this see “System Test Mode” on

page 3.

The CTS T

YPE option allows the clear to set signal to be set to either N/O or N/C. To

set the CTS type:

1. From the I

NSTALL & SERVICE menu, use the Up and Down buttons to navigate to

the CTS T

YPE prompt; press the Enter button.

2. The CTS OP N/O, N/C prompt displays. Use the Up and Down buttons to choose

N/O or N/C; press Enter to select.

1 2 3 4

Comments to this Manuals

No comments

Inovonics EE4216MR User Manual Page 2

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Inovonics EE4216MR