Inovonics EN4216MR User Manual download pdf (Page 4)

4. RESET CONFIG? displays; select Y and press the Enter button

9.3 Change Password

Passwords can be up to eight digits long. The default password is 3446. To

change the password:

1. From the I

NSTALL & SERVICE menu, press Enter at the CHANGE

PASSWORD prompt.

2. Use the Up/Down buttons to scroll through the digits; press Enter to

select and advance to the next digit.

Note: Choosing a null as the password will disable the function, allowing

users to perform receiver functions and/or change parameters without a

password.

3. When finished, press Enter again to complete selection.

4. When P

ASSWORD CHANGED displays, press Enter to return to the

NSTALL & SERVICE menu.

Caution: Store the new password in a secure place. If the new password is

lost, you will not be able to access the receiver without restoring it to factory

defaults as described in section 9.2, “Factory Config” on page 3.

9.4 Signal Strength

The SIGNAL STRENGTH option is used to measure signal strength and

troubleshoot installation problems.

1. At the S

IGNAL STRENGTH prompt, press Enter.

• The first programmed point displays, along with a signal quality of

GOOD, WEAK or NO SIG.

Note: The point must have an active transmitter associated with it to

display signal strength.

2. Use the Up/Down buttons to scroll through the registered transmitters.

3. Press Enter to view Level (LV) and Margin (MA).

4. LV indicates the overall signal strength; MA indicates the signal strength

minus the background noise.

Note: Inovonics recommends an LV of four for most installations.

9.5 Delete Point

The DELETE POINT option allows you to delete transmitter registration

information from all registered points, or from a specific point. Programmed

point information is not deleted; just the registration identification number

associated with the transmitters or repeaters. To delete points:

1. From the I

NSTALL & SERVICE menu, use the Up and Down buttons to

navigate to the DELETE POINT prompt; press the Enter button.

2. The DELETE ALL? prompt displays. Use the Up and Down buttons to

choose N for no or Y for yes; press Enter to select.

3. If you selected no, the D

ELETE POINT prompt displays. Use the Up and

Down buttons to choose a point to delete; press Enter to select.

4. Press the Enter button. If there is more than one registered point, then

pressing the Enter button returns to point selection for deletion; if there

are no more registered points, the display returns to the I

NSTALL &

ERVICE menu.

9.6 Register Transmitter

The REGISTER XMITTER option allows you to register a transmitter or

repeater.

1. From the I

NSTALL & SERVICE menu, use the Up and Down buttons to

navigate to the REGISTER XMITTER prompt; press the Enter button.

2. Use the Up and Down buttons to choose the point to which you want to

3. Press the transmitter/repeater’s Reset button at the R

ESET XMITTER

prompt.

10 Event Log

The event log displays the last 50 events that have occurred, whether they

be alarms, or tamper or inactive faults. Event log information is available

without a password.

1. From system status information, press Enter.

2. Use the Up or Down buttons to navigate to E

VENT LOG; press the Enter

button.

3. Use the Up/Down buttons to scroll through events.

4. When viewing transmitter events, press Enter to see the output the

events map to.

Note: No output will be displayed if the event is mapped to a null output.

11 Specifications

Compatible repeater, transmitters: EN5040-T, EN1215EOL, EN1215WEOL,

EN1223D, EN1235SF, EN1235DF, EN1249, EN1261HT

Dimensions: 165 mm x 89 mm x 25 mm (6.5" x 3.5" x 1").

Weight: 280 g (.62 lb)

Operating environment: 0°- 60°C (32°- 140°F), 90% relative humidity,

non-condensing.

Power requirement: 11 - 14 VDC; 400 mA

Output specifications: Form C relay 1A @ 28 VDC, 0.5 @ 30 VAC

resistive load

Input specifications: A low is less than .5 V; a high is greater than 2.5 V.

Reset input: Contact closure, momentary low.

Receiver type: Frequency hopping spread spectrum.

Operating frequency: 915-928 MHz (Australia), 921-928 MHz (New

Zealand), 902-928 MHz (USA)

Tamper: Type B, fixed device.

Number of points/Transmitters: 16.

Number of outputs: Six Form C relay outputs

Event history log capacity: 50 events (first-in, first-out replacement).

UL listings: UL 365, UL 636, UL 1023, ULC/ORD-C1023-74, UL 1076, UL

1610.

Figure 5 Tamper, Reset, Arm and Receiver Operational Circuits

12 Television and Radio Interference

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

13 Warranty and Disclaimer

Note: Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the

equipment.

Inovonics Wireless Corporation ("Inovonics") warrants its products

("Product" or "Products") to conform to its own specifications and to be free

of defects in materials and workmanship under normal use for a period of

thirty-six (36) months from the date of manufacture. Within the warranty

period, Inovonics will repair or replace, at its option, all or any part of the

warranted Product. Inovonics will not be responsible for dismantling and/or

reinstallation charges. To exercise the warranty, the User ("User", "Installer"

or "Consumer") must work directly through their authorized distributor who

will be given a Return Material Authorization ("RMA") number by Inovonics.

Details of shipment will be arranged directly through the authorized

distributor.

This warranty is void in cases of improper installation, misuse, failure to

follow installation and operating instructions, alteration, accident or

tampering, and repair by anyone other than Inovonics.

This warranty is exclusive and expressly in lieu of all other warranties,

obligations or liabilities, whether written, oral, express, or implied. There is

no warranty by Inovonics that Inovonics product will be merchantable or fit

for any particular purpose, nor is there any other warranty, expressed or

implied, except as such is expressly set forth herein. In no event shall

Inovonics be liable for an incidental, consequential, indirect, special, or

exemplary damages, including but not limited to loss of profit, revenue, or

contract, loss of use, cost of down time, or interruption of business, nor any

claim made by distributor's customers or any other person or entity.

This warranty will not be modified or extended. Inovonics does not

authorize any person to act on its behalf to modify or extend this warranty.

This warranty will apply only to Inovonics Products. Inovonics will not be

liable for any direct, incidental, or consequential damage or loss

whatsoever, caused by the malfunction of Product due to products,

accessories, or attachments of other manufacturers, including batteries,

used in conjunction with Inovonics Products.

Note: E-mail [email protected] for a copy of the CE Declaration of

Conformity.

GND

Tamper

Reset

Receiver Power Loss

Jam

1 2 3 4 5 6 7 8 9 10

Comments to this Manuals

No comments

Inovonics EN4216MR User Manual Page 4

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Inovonics EN4216MR